Introduction to Using the Light Microscope

I. Determining Diameter of Field

1. Rotate the nosepiece to low-power magnification. Place a clear plastic ruler on the microscope stage and focus on the millimeter divisions along the edge of the ruler.
a) Measure and record the diameter of the field of view by counting the number of millimeter divisions. Estimate to the nearest 0.5 mm.
b) Convert millimeters to micrometers (µm). (1 mm = 1000 µm.)

2. The field of view for both medium and high-power magnification can be determined indirectly by calculating the ratio quotient of the high-power objective lens to the low-power objective lens. Calculate the ratio quotient for each lens.

c) Ratio quotient =	magnification of desired lens
	magnification of low power lens

3. Calculate the diameter of the field of view for both the medium and high-power objectives (use micrometers).

d) Desired lens diameter =	low-power field diameter
	ratio quotient

Observing a Specimen

4. Locate and cut out a lower case letter "e" from the newspaper and prepare a wet mount (See Nelson Biology, page 38).

5. Adjust the nosepiece so the low power objective lens is in place and clip the slide in place.

6. Using the coarse adjustment knob and by moving the slide as required, locate the "e" under low power. Be careful not to allow the lens to touch the slide. It is easier on your eyes if you keep both eyes open while looking through the ocular lens (this takes some practice).
e) Describe the orientation of the "e" as seen through the microscope.
f) If the slide is moved to the right, in which direction does the "e" appear to move?

7. With the specimen centered in the field of view and in focus, rotate the nosepiece so that the medium power objective lens is in place. Bring the specimen into focus using the fine adjustment knob.
g) How does the size of the "e" seem to change?

8. With the specimen centered in the field of view and in focus, rotate the nosepiece so that the high power objective lens is in place. Bring the specimen into focus using the fine adjustment knob.
h) Do you see more or less of the letter?
i) Under which magnification is the image brought closer to the eye?
j) Which magnification would be most suited for scanning several objects?
k) Which magnification provides the widest angle for viewing?

9. Cut a 1 cm square out of a newspaper picture and prepare a wet mount

Questions

1. When centering an object under the microscope you move it from left to right, which way does it appear to move? When you move it away from you, how does it appear to move?

2. Is it easier to locate objects under low or high power?

3. Why is it a good idea to centre a specimen in the field of view before switching to a higher power?

4. If you were trying to estimate the diameter of a small object, which magnification would you use?

5. Explain why microscopes are stored with the low power lens in position?

6. Why should the coarse adjustment focus not be used with a medium or high power lens?

7. A thicker lens is often necessary for greater magnification, but results in a loss of resolving power. Explain why resolving power decreases as the thickness of the lens increases.

8. Why is the microscope called a compound microscope?

9. What is the proper way to carry a microscope?

10. How do you determine total magnification?

11. What is the total magnification of each of the objective lenses on your microscope?

12. Why is the built in pointer a useful feature of the microscope?

13. Why are micrometers rather than millimeters used for microscopic measurements?

14. Why is the field of view brighter under low power?

Application Questions

15. A student switches from the low- to the high-power objective lens of a microscope. The object being viewed disappears, even after careful focusing. Indicate why the object cannot be seen, and suggest a technique that would help eliminate this problem.

16. An oil immersion lens is often used to view very tiny objects. If an oil immersion lens has a magnification of 100x, calculate its field of view.

17. A correcting lens can be placed into the microscope to make objects appear in their normal (non-reversed) position. Suggest reasons why this would be useful.

18. Why is it important to measure the size of microscopic objects?